What is the difference between RIPv1 and v2?
RIP v1 is an older, no longer much used routing protocol. RIP v2 is a classless protocol and it supports classful, variable-length subnet masking (VLSM), CIDR, and route summarization. RIPv2 supports authentication of RIPv2 update messages (MD5 or plain-text).
Which RIP version should I use?
RIP-1 is universally supported. RIP-1 is probably adequate for most networks, unless you have an unusual network setup. RIP-2 carries more information.
What is difference between RIPv1 and RIP v2 and give commands for RIPv1 used in practical?
RIPv2 is a classless, distance vector routing protocol as defined in RFC 1723. Being a classless routing protocol, means, it includes the subnet mask with the network addresses in its routing updates….Differences between RIPv1 and RIPv2 :
| SR.NO | RIPv1 | RIPv2 |
|---|---|---|
| 2. | It can supports class full network only. | It can support class full and classless networks. |
Why do we use RIP version 2?
RIP uses the hop count as a routing metric. RIP prevents routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for RIP is 15. RIP version 2 (RIPv2) was developed due to the deficiencies of the original RIP.
What is the main disadvantage of using RIP?
This is one of the biggest disadvantages of RIP. Bandwidth utilization in RIP is very high as it broadcasts its updates every 30 seconds. RIP supports only 15 hop count so a maximum of 16 routers can be configured in RIP. Here the convergence rate is slow.
What is RIP v2?
RIP v2 is a classless protocol and it supports variable-length subnet masking (VLSM), CIDR, and route summarization. RIPv1 routing updates are broadcasted. RIP v2 routing updates are multicasted.
What is WIFI RIP?
Routing Information Protocol (RIP) is a protocol that routers can use to exchange network topology information. It is characterized as an interior gateway protocol, and is typically used in small to medium-sized networks. The routing table is broadcast to all stations on the attached network.
What is the advantage of RIP?
Bandwidth utilization in RIP is very high as it broadcasts its updates every 30 seconds. RIP supports only 15 hop count so a maximum of 16 routers can be configured in RIP. Here the convergence rate is slow. It means that when any link goes down it takes a lot of time to choose alternate routes.
Is RIP v2 still used?
RIPv2 was first described in RFC 1388 and RFC 1723 (1994); the current RFC is 2453, written in November 1998. Although current environments use advanced routing protocols such as OSPF and EIGRP, there still are networks using RIP.
What’s the difference between Rip ver1 and RIP v2?
RIP Ver1. RIP Ver2. RIP v1 uses what is known as classful routing. RIP v2 is a classless protocol and it supports variable-length subnet masking (VLSM), CIDR, and route summarization. RIPv1 routing updates are broadcasted. RIP v2 routing updates are multicasted. RIPv1 has no authentication. RIP v2 supports authentication.
What is the Routing Information Protocol ( RIP ) v1?
Routing Interface Protocol (RIP) V1 & V2. Routing Information Protocol (RIP) protocol are the intradomain (interior) routing protocol which is based on distance vector routing and it is used inside an autonomous system.Routers and network links are called node.
What’s the difference between RIPv1 and classful routing?
Classful routing protocols support only the networks which are not subnetted. Classful routing protocols do not send subnet mask information with their routing updates. In other words, if you have a subnetted network in your RIPv1 routing domain, RIPv1 will announce that network to other as unsubnetted network.
What are the benefits of RIP version 2?
RIP Version-2: 1 It’s a standardized protocol. 2 It’s VLSM compliant. 3 Provides fast convergence. 4 It sends triggered updates when the network changes. 5 Works with snapshot routing – making it ideal for dial networks. More